二手標量網絡分析儀54147A  ANRITSU 熊生：13751228936
東莞市創源電子儀器有限公司
　   54100A系列網絡分析儀可提供設備特性。設備包括：放大器、天線、適配器、RF電橋、電纜、波相傳輸線、接收器、衰減器、VCO、開關、耦合器、過濾器等。先進的軟硬件特性可加速生產力和提高準確性。結合自動波段搜索功能加快調節速度。低源同步和高指向性SWR自動測試儀確保準確。 
★快速準確的測量傳輸、返回損耗及精確性返回損耗、SWR、群延遲、絕對功率和距離誤差。
★晶體源特別穩定和準確。 
★內置自動化特征包括距離誤差
★內置磁盤驅動
★結實可靠的機箱
★傳輸收益（損耗），群延遲和功率測量
★傳輸及返回損耗（或SWR）
★適配器、衰減器、終端、耦合器及RF電橋 
★54107A 純量測試系統（0.001-1.5GHz） 
特點
    54100A系列網絡分析儀可提供設備特性。設備包括：放大器、天線、適配器、RF電橋、電纜、波相傳輸線、接收器、衰減器、VCO、開關、耦合器、過濾器等。先進的軟硬件特性可加速生產力和提高準確性。結合自動波段搜索功能加快調節速度。低源同步和高指向性SWR自動測試儀確保準確。 
★快速準確的測量傳輸、返回損耗及精確性返回損耗、SWR、群延遲、絕對功率和距離誤差。
★晶體源特別穩定和準確。 
★內置自動化特征包括距離誤差
★內置磁盤驅動
★結實可靠的機箱
★傳輸收益（損耗），群延遲和功率測量
★傳輸及返回損耗（或SWR）
★適配器、衰減器、終端、耦合器及RF電橋 
★54107A 純量測試系統（0.001-1.5GHz） 
技術指標
Analyzer Measurement modes Transmission(dB),return loss(dB),SWR(linearSWR),optiona group delay(ns),power(dBm)precision return loss(dB) and optionaldistance-to-fault 
Dynamic range -55 to +16dBm,autozeroing with DC detection 
Inputs Three,two standard inputs,A and B,with optionathird reference channel,R(Option 5) 
Display channels Two channels are used to select and simultaneouslydisplay any two inputs fromA,B,or R.The inputs can also be displayed asratios A/R or B/R. 
Scale resolution 0.1 to 10dB(m) per division in 0.1dB steps 
Cursor functions Searches for trace maximum,minimum,dB level,dBbandwidth,next marker and active marker 
Averaging 2,4,8,16,32,64,128,or 256 
Limit lines Two limit ines,either single value or multilevel segmented,for each trace.Segmented lines may be made from up to 10individually editable segments. 
Auto-zero Performs an AC modulation cycle and lowlevel calibration during sweeper ratrace 
Save/Recall Thirteen sets of front panel set-ups andthirteen sets of trace memory can be stored in non-volatile instrument memory. 
Trace mask A swept frequency measurement can be storedto a graticule trace mask for visual comparison to later measurements. 
Disk drive Built-in 3.5 inch,1.44MB floppy disk drive 
Autosave Automatically increments the trace datafile name and reference number during successive data storage operationsto the DOS disk 
Source Frequency range 1Mhz to 110GHz,model dependent 
Alternate sweep Sweep alternately between frequenc yrangesset differently for channel 1 and channel 2 
CW Provides single frequency output(both channelsturned off) 
Frequency resolution Rf Model(54107A,54109A,54111A):10kHz,Microwavemodels:100khz 
Output power Maximum guaranteed levelled output poweris model dependent. 
Reverse power protection UP to 5 Watts.Limited to 1 Watt with attenuatoroption 
Appli-
cation function Min/Max hold Save the minimum and maximum values of successivesweeps or the combination of the two 
Cursor functions Automatic cursor seach updates the bandwidth,minimum,ormaximum levels of the displayed trace. 
Compression test automation Determines the gain compression point overthe operating freqeuncy range of an ampliffier by successively incrementingthe source power and measuring the amount of compression until a preset"X"dBlimit is exceeded. 
Self test Performs a self test every time power isapplied or when SELF TEST pushbutton is pressed.If an error is detected,adiagnostic code appears,identifying the cause and location of the error. 
General Operating temperature 0°to 50℃ 
Power 48 to 400Hz,300VA 
Mass 18kg(39lb.) 
Printer Parallel printer interface is compatiblewith the Canon BJ30,Bj200e,and most Epson FX-compatible printers. 
Transit case Hard shell case with custom foam inserts,PN:760-183 
EMC Meets European community requirements forCE marking 
訂貨信息 Model/Order No. Name 
Option 1 Options 
Rack mounting with slides 
Option 2 70dB RF step attenuator 
Option 2A 70dB,20Ghz MW step attenuator 
Option 2B 70dB,26.5GHz MW step attenuator 
Option 2C 70dB,40GHz MW step attenuator 
Option 2D 70dB,50GHz MW step attenuator 
Option 4 75Ω source output(available to 3.0GHz) 
Option 5 Add reference channel 
Option 6 Add external levelling 
Option 7 Internal distance-to-fault software 
Option 8 Internal relative group delay software 
Option 12 Add front panel cover 
Option 13 Add front mounted handles 
Option 16 +15V DC supply for millimeter wave source modules(availablewith<20GHz models only) 
Option 25 Maintenance manual 
Option 26 Extra operation and GPIB programming manual 
Option 33 Canon printer