塑料滑動摩擦磨損試驗機  功能：

    本廠生產的計算機控制塑料滑動摩擦試驗機是在現有電子塑料滑動摩擦試驗機的基礎上又增加了很多試驗功能，可以同時顯示扭矩-時間曲線，隨意設定試驗次數，顯示當前試驗次數，設定時間及當前試驗時間等多種功能，本機還配有彩色打印機，可以打印出帶有曲線，表格數據，試驗單位名頭的精美的試驗報告單。

塑料滑動摩擦磨損試驗機   特點：

1、系統運行穩定，可靠性高。

2、結構緊湊，使用方便，簡單。

3、采用高精度電機、驅動機、傳感器，精度高。

4、具有試驗人員分級管理功能。

5、實時顯示摩擦系數-時間，扭矩-時間曲線。

6、試驗報告可打印試驗參數，試驗數據，曲線，備注等信息，簡單，方便，可編輯。

7、試樣尺寸： 30mm?7mm?6mm

8、轉動速度： 0-500轉/分 （可調）

9、負 荷： 196N ? 0.1%（可增至392N）

10、摩擦環尺寸：￠40?10mm ，倒角0.5?45?，外圓表面與內圓同心度偏差小于0.01

11、摩擦環材質：45號鋼,淬火,熱處理HRC40-45,外圓表面光潔度▼8

12、摩擦力矩： 0--4N?m

13、砝碼重量：4KG砝碼一件，1KG砝碼4件，可實現重量疊加功能。

技術參數：

1、速度精度：1%

2、負荷精度：0.5%

3、摩擦力矩精度：1%

4、計數器精度：1S

5、傳感器測量精度：1% FS

符合標準：

GB/T 3960-1983 塑料滑動摩擦磨損試驗方法 GB/T 9141.8-1999 柔性石墨板材滑動摩擦系數測試方法

主要配置及附件：（計算機控制）

1、試驗主機一臺

2、高精度扭矩傳感器一只

3、計算機數據采集卡一塊

4、計算機一臺（品牌）

5、彩色激光噴墨打印機一臺

6、計算機控制軟件一套

7、4Kg 砝碼兩件（備用一套）

8、標準磨擦環四件（備用兩件）

9、產品使用說明書一份

10、產品合格證

11、產品裝箱單一份

12、整機重量：約87 公斤

硬件安裝及連線

 1、將電源線插入設備后邊的電源插口。

 2、將控制和采集線一端接到設備控制端口，另一端接到計算機上。

 3、正確連接電腦接線

試樣要求

試樣表面平整，無氣泡、裂紋、分層、明顯雜質和加工損傷等缺陷。每組試樣不少于3個。

試驗條件

試驗中上轉軸保持靜止，下轉軸以200轉/分轉動,摩擦副做滑動摩擦,對磨2小時,負荷20公斤,根據材料,允許選擇其它負荷.試驗環境溫度為23?5攝氏度.

試驗報告

試驗報告應包括下列內容：

A.塑料名稱、規格、牌號、生產廠；

B.試樣的制備方法，摩擦表面狀況，測定的試樣個數；

C.環境溫度、溫度及狀態調節條件；

D.圓環材質、硬度、光潔度和外徑尺寸；

E.試驗負荷；

F.試驗結果：磨痕寬度或體積磨損及摩擦系數的測定結果；

G.試驗日期、人員。

試驗步驟

1、圓環應清除油污，貯存于干燥缸內以防生銹。

2、試樣經狀態調節后用感量為0.1毫克的分析天平稱取其質量（M1）。

3、把試樣裝進夾具，摩擦面用角尺校正并使它與圓環的交線外于試樣正中。裝好摩擦力矩記錄紙，開機校好零點。

4、再次用乙醇、丙酮等不與塑料起作用的溶劑仔細清除試樣和圓環上的油污，此后不準再用手接觸試樣和圓環的表面。

5、平穩地加荷至選定的負荷值。

6、對磨2小時后停機卸負荷，取下試樣和圓環，清理試樣表面后，用精度不低于0.02毫米的量具測量磨痕寬度，或在試驗環境下存放1小時后稱取試樣質量（m2)。

7、讀取摩擦力矩值。

狀態調節

狀態調節按GB2918-82《塑料試樣狀態調節和試驗的標準環境》進行，溫度為23?5攝氏度，溫度為50?10%。

Function:

The computer-controlled plastic sliding friction testing machine produced by our factory has added many testing functions on the basis of the existing electronic plastic sliding friction testing machine. It can simultaneously display the torque time curve, freely set the number of tests, display the current number of tests, set the time and the current test time, and other functions. The machine is also equipped with a color printer, which can print exquisite test reports with curves, table data, and test unit names.

characteristic:

1. The system runs stably and has high reliability.

2. Compact structure, easy to use, and simple.

3. Adopting high-precision motors, drivers, and sensors, with high precision.

4. It has the function of grading and managing experimental personnel.

5. Real time display of friction coefficient time and torque time curves.

6. The test report can print test parameters, test data, curves, notes, and other information, which is simple, convenient, and editable.

7. Sample size: 30mm?7mm?6mm

8. Rotation speed: 0-500 revolutions per minute (adjustable)

9. Load: 196N ? 0.1% (can be increased to 392N)

10. Friction ring size:￠40 ? 10mm, chamfer 0.5 ? 45 ?, concentricity deviation between outer and inner surfaces less than 0.01

11. Friction ring material: 45 steel, quenched, heat treated HRC40-45, outer surface smoothness ▼ 8

12. Friction torque: 0--4N?m

13. Weight of weights: One 4KG weight and four 1KG weights, which can achieve weight stacking function.

Technical parameters:

1. Speed accuracy: 1%

2. Load accuracy: 0.5%

3. Friction torque accuracy: 1%

4. Counter accuracy: 1S

5. Sensor measurement accuracy: 1% FS

Compliant with standards:

GB/T 3960-1983 Plastic Sliding Friction and Wear Test Method GB/T 9141.8-1999 Flexible Graphite Sheet Sliding Friction Coefficient Test Method

Main configuration and accessories: (computer-controlled)

1. One experimental host

2. One high-precision torque sensor

3. One computer data acquisition card

4. One computer (brand)

5. One color laser inkjet printer

6. A set of computer control software

7. Two 4Kg weights (one set for backup)

8. Four standard friction rings (two spare)

9. One copy of the product user manual

10. Product Qualification Certificate

11. Product packing list copy

12. Whole machine weight: approximately 87 kilograms

Hardware installation and wiring

1. Insert the power cord into the power socket at the back of the device.

2. Connect one end of the control and acquisition cable to the device control port and the other end to the computer.

3. Connect the computer wiring correctly

Sample requirements

The surface of the sample is flat, without defects such as bubbles, cracks, delamination, obvious impurities, and processing damage. Each group shall have no less than 3 samples.

Experimental conditions

In the experiment, the upper shaft remains stationary and the lower shaft rotates at 200 revolutions per minute. The friction pair performs sliding friction and grinds for 2 hours with a load of 20 kilograms. Depending on the material, other loads can be selected The experimental environment temperature is 23 ? 5 degrees Celsius

Test report

The test report should include the following contents:

A. Plastic name, specification, brand, and manufacturer;

B. The preparation method of the sample, the condition of the friction surface, and the number of samples measured;

C. Environmental temperature, temperature and state regulation conditions;

D. Circular ring material, hardness, smoothness, and outer diameter size;

E. Test load;

F. Test results: Measurement results of abrasion width or volume wear and friction coefficient;

G. Test date and personnel.

Experimental steps

1. The circular ring should be cleaned of oil stains and stored in a drying cylinder to prevent rusting.

2. After adjusting the state of the sample, weigh its mass (M1) using an analytical balance with a sensitivity of 0.1 milligrams.

3. Insert the sample into the fixture, calibrate the friction surface with an angle ruler, and ensure that its intersection with the circular ring is outside the center of the sample. Install the friction torque recording paper and start the machine to calibrate the zero point.

4. Carefully remove the oil stains on the sample and the ring using solvents such as ethanol and acetone that do not work with plastic. After that, do not touch the surface of the sample and ring with your hands.

5. Smoothly load to the selected load value.

6. After grinding for 2 hours, stop the machine to unload the load, remove the sample and ring, clean the surface of the sample, measure the width of the grinding mark with a measuring tool with an accuracy of not less than 0.02 millimeters, or weigh the sample mass (m2) after storing it in the test environment for 1 hour.

7. Read the torque value of friction force.

State adjustment

The state adjustment shall be carried out in accordance with GB2918-82 "Standard Environment for State Adjustment and Testing of Plastic Specimens", with a temperature of 23 ? 5 degrees Celsius and a temperature of 50 ? 10%.

我廠主要產品有：拉力材料試驗機，海綿泡沫落球回彈試驗機，海綿泡沫壓陷硬度測驗儀，海綿泡沫疲勞壓陷試驗機，熔融指數儀，塑料滑動摩擦磨損試驗機，電壓擊穿試驗儀，塑料球壓痕硬度計，馬丁耐熱試驗儀，海綿泡沫拉伸強度試驗機，介電常數與介質損耗測試儀，電容率測試儀，體積表面積電阻率測試儀，低溫脆性沖擊試驗儀，維卡熱變形試驗儀，啞鈴制樣機，阿克隆磨耗試驗機，簡支梁沖擊試驗機，懸臂梁沖擊試驗機，熔體流動速率儀，無轉子硫化儀等。

 想了解其它相關信息，歡迎登錄北京北廣精儀儀器設備有限公司網站或電詢我們相關人員。

關于儀器質保：1、北廣儀器保證提供的設備為需方指定的全新設備，其各項技術指標均符合相關的產品技術要求。2、設備經客戶驗收合格后，開始計算保修期，設備免費保修期為壹年，設備在質量保質期內，產品在非人為損壞的情況下，由北廣儀器負責全保。北廣儀器的客服在得到通知后24小時內響應，安排約定維修細節。3、質保期后，我們免費為您維修維護設備，除大型設備外所有設備一律返廠維修，經檢驗后，電話告知客戶問題所在及解決方式，經客戶同意后進行維修，維修后發回客戶，對于損壞及更換的零部件我們只收取成本費；如客戶不認同我們的檢驗結果，雙方另協商維修細節。