10KN電子安全繩拉力拉伸試驗機  Software features:

 10KN電子安全繩拉力拉伸試驗機

1. Modular functionality of testing standards: Provides users with the ability to set testing standards for their desired applications, covering testing standards and specifications such as GB, ASTM, DIN, JIS, BS, etc.

2. Sample data: Provide users with the ability to set all sample data, input data once for permanent reuse, and modify formulas to improve test data fit.

3. Dual report editing: Fully open for users to edit reports, allowing testers to choose their preferred report format (the test program has added built-in EXCEL report editing functionality, expanding the previous single professional report format).

4. The lengths, force units, and display digits are dynamically interchanged, with force units of T, Kg, N, KN, 5, and lb, and deformation units of mm, cm, and inch.

5. The graph curve scale is automatically optimized by Auto Scale, which can display the graph at the optimal scale and dynamically switch the graph in real-time during testing. It has load displacement, load time, displacement time, stress-strain load-2 point extension diagrams, as well as multi curve comparisons.

6. The test results can be output in the form of WORD and EXCEL data formats.

7. After the test is completed, it can be automatically archived or manually archived. After the test is completed, the maximum strength, upper and lower yield strength, hysteresis loop, stepwise approximation method, non proportional elongation strength, tensile strength, compressive strength, tensile strength at any point, tensile strength at any point, elastic modulus, elongation rate, stripping interval maximum and minimum values, average value, net energy, folding energy, total energy, bending modulus, breakpoint displacement x% load, breakpoint load X% displacement, and so on can be automatically calculated.

8. Data backup: Test data can be saved on any hard drive partition.

9. The software has the function of demonstrating historical tear strength test data.

10. Common testing items: (common display values and calculated values)

● Tensile stress ● Tensile strength

● Tensile strength ● Tensile elongation

● Constant tensile stress ● Constant elongation at constant stress

● Fixed stress value ●

● Force value at any point ● Elongation at any point

● Extraction force ● Adhesive force and peak calculation value

● Pressure test ● Shear peeling force test

● Bending test ● Pull out force puncture force test

11. Special testing items:

A. The elastic coefficient, also known as the Young's modulus of elasticity, is defined as the ratio of the normal stress component to the normal strain in the same phase. To determine the coefficient of material rigidity, the higher the value, the stronger the material.

B. Proportional limit: The load can maintain a proportional relationship with elongation within a certain range, and its maximum stress is the specific limit.

C. Elastic limit: The maximum stress that a material can withstand without permanent deformation.

D. Elastic deformation: After removing the load, the deformation of the material completely disappears.

E. Permanent deformation: After removing the load, the material still retains deformation.

F. Yield point: When a material is stretched, the deformation increases while the stress remains constant, and this point is called the yield point. The yield point is divided into upper and lower yield points, and generally the upper yield point is taken as the yield point. Yield: When the load exceeds the proportional limit and elongation is no longer proportional, the load will suddenly drop, and then fluctuate up and down over a period of time, causing significant changes in elongation. This phenomenon is called yield.

G. Yield strength: The quotient obtained by dividing the load at which the permanent elongation reaches a specified value during stretching by the original cross-sectional area of the parallel part.

H. Spring K value: the ratio of the force component in phase with the deformation to the deformation.

I. Effective elasticity and hysteresis loss:

On a tensile testing machine, when the specimen is stretched at a certain speed to a certain elongation or to a specified load, the percentage of the recovered work during shrinkage and the consumed work during stretching is measured as the effective elasticity; The percentage of the energy lost during the elongation and contraction of a sample compared to the work consumed during elongation is called hysteresis loss.

軟件特點:

1、測試標準模塊化功能:提供使用者設定所需應用的測試標準設定，范圍涵蓋GB、ASTM、DIN、JIS、BS…等測試標準規范。

2、試品資料:提供使用者設定所有試品數據，一次輸入數據永久重復使用，并可自行增修公式以提高測試數據契合性。
3、 雙報表編輯:完全開放式使用者編輯報表，供測試者選擇自己喜好的報表格式(測試程序新增內建EXCEL報表編輯功能擴展了以往單一專業報表的格局) 。
4、 各長度、力量單位、顯示位數采用動態互換方式，力量單位T、Kg、N、KN、5、lb，變形單位mm、cm、inch。
5、圖形曲線尺度自動醉佳化Auto Scale，可使圖形以醉佳尺度顯示，并可于測試中實時圖形動態切換。具有荷重-位移、荷重-時間、位移-時間、應力-應變荷重-2點延伸圖，以及多曲線對比。
6、測試結果可以WORD、EXCEL格式的數據形式輸出。

7、測試結束可自動存檔、手動存檔，測試完畢自動求算醉大力量、上、下屈服強度、滯后環法、逐步逼近法、非比例延伸強度、抗拉強度、抗壓強度、任意點定伸長強度、任意點定負荷延伸、彈性模量、延伸率、剝離區間醉大值、醉小值、平均值、凈能量、折返能量、總能量、彎曲模量、斷點位移x％荷重、斷點荷重X％位移、等等。
8、數據備份：測試數據可保存在任意硬盤分區。
9、軟件具有歷史撕裂強度測試數據演示功能。

10、普通測試項目：(普通顯示值及計算值)
            ●拉伸應力   ●拉伸強度
            ●扯斷強度   ●扯斷伸長率
            ●定伸應力   ●定應力伸長率
            ●定應力力值  ●
            ●任意點力值  ●任意點伸長率
            ●抽出力    ●粘合力及取峰值計算值
            ●壓力試驗   ●剪切力剝離力試驗
            ●彎曲試驗   ●拔出力穿刺力試驗

11、特殊測試項目： 

A.彈性系數即彈性楊氏模量定義：同相位的法向應力分量與法向應變之比。為測定材料剛性之系數，其值越高，材料越強韌。
B.比例限：荷重在一定范圍內與伸長可以維持成正比之關系，其醉大應力即為比極限。
C.彈性限：為材料所能承受而不呈永久變形之醉大應力。
D.彈性變形：除去荷重后，材料的變形完全消失。
E.永久變形：除去荷重后，材料仍殘留變形。
F.屈服點：材料拉伸時，變形增快而應力不變，此點即為屈服點。屈服點分為上下屈服點，一般以上屈服點作為屈服點。屈服(yield)：荷重超過比例限與伸長不再成正比，荷重會突降，然后在一段時間內，上下起伏，伸長發生較大變化，這種現象叫作屈服。
G.屈服強度：拉伸時，永久伸長率達到某一規定值之荷重，除以平行部原斷面積，所得之商。
H.彈簧K值：與變形同相位的作用力分量與形變之比。
I.有效彈性和滯后損失：
在拉力試驗機上，以一定的速度將試樣拉伸到一定的伸長率或拉伸到規定的負荷時，測定試樣收縮時恢復的功和伸張時消耗的功之比的百分數，即為有效彈性；測定試樣伸長、收縮時所損失的能與伸長時所消耗的功之比的百分數，即為滯后損失。

常見故障：

1：上升、下降、試驗操作時，按下鍵后顯示停止

  解決方案：1：檢查系統設置當前量程設置和過載保護率

            2：檢查速度參數是否變化

            3：檢查傳感器是否過載

2：上電后儀表藍屏

解決方案：1：重新上電

           2：重新上電如果不行，拿到沒有干擾的地方上電試一下

           3：聯系生產廠家更換液晶屏

3：橫梁不移動

 解決方案：1：檢查數據線是否連接號

           2：檢查是否過載，傳感器是否損壞

           3：是否限位，移動磁鐵

4：儀表不準確

解決方案：  1：傳感器是否損壞

             2：調整了標定系數

             3：是否年檢

Common faults:

1: When performing ascending, descending, or experimental operations, pressing the key will display 'stop'

Solution: 1: Check the current range setting and overload protection rate of the system settings

2: Check if the speed parameters have changed

3: Check if the sensor is overloaded

2: Blue screen on the instrument panel after power on

Solution: 1: Power on again

2: If it doesn't work, try powering it on in a place without interference

3: Contact the manufacturer to replace the LCD screen

3: The crossbeam does not move

Solution: 1: Check if the data cable has a connection number

2: Check if there is overload and if the sensor is damaged

3: Is there a limit, move the magnet

4: Inaccurate instrument

Solution: 1: Is the sensor damaged

2: Adjusted the calibration coefficient

3: Is it an annual inspection

關于儀器返廠維修：1、維修維護全面 ：設備損壞后，使用者往往對設備損壞情況描述不清、不全面，經常會出現技術人員到達現場之后，發現工具不全或者零配件需要更換卻沒有提前準備零配件，常常會造成被動或者維修遲緩的局面，耽誤客戶使用。設備返廠維修，廠內零配件及工具齊全，技術人員在維修設備同時，按照公司要求會利用廠內設施為返廠的設備做系統的維護，將一些細微的毛病及早解決。2、響應速度快 ：設備損壞后，我們即使以最快的速度為您安排相關的技術人員出差，也要走流程等待技術部門安排具體的人員出差，往往需要一定時間。有時因為技術人員連續出差，耽擱在某地，偶爾還會耽誤與客戶提前約定好的時間。 現在物流快遞行業發達，全國各地運輸都很快捷方便，返廠維修往往能更省事省力。

Function Introduction:

After the sample is damaged, the moving crossbeam will automatically stop moving (or return to its initial position)

Automatic shifting automatically switches to the appropriate range based on the magnitude of the test force to ensure the accuracy of the measurement data

The experimental conditions and sample raw data of the conditional module can be stored in the form of their own standard modules; Convenient for users to access and view, saving testing time with automatic transmission

The displacement speed or loading speed during the automatic transmission test process can be automatically completed according to a pre programmed and set program, or manually changed

Automatic saving of the experiment ends, and the experimental data and curves are automatically saved by the computer to prevent data loss caused by forgetting to save them

The testing process, measurement, display, analysis, etc. are all completed by microcomputers

Display method: Data and curves are dynamically displayed during the experimental process

Experimental software with Chinese Windows user interface, easy to operate

The test report can be edited and printed according to user requirements

Batch testing can be completed sequentially for samples with the same parameters after one setting

According to the testing requirements, the automatic process allows users to easily establish their own testing templates (methods, etc.) for easy secondary calling, and can achieve closed-loop testing control of loading speed, stress, and strain

After the completion of the curve traversal experiment, the curve can be enlarged and reanalyzed, and the data corresponding to each point on the experimental curve can be found with the mouse

Users can add test methods according to the test requirements

The limit protection has two levels of programmable and mechanical limit protection

Overload protection automatically shuts down when the load exceeds the rated value by 3-5%

The report displays both automatic and manual modes for obtaining various experimental results, automatically forming reports to simplify the data analysis process and facilitate users

附件：

★一年保固書及中文操作說明書各一份。

★隨機贈送標準全拉力試驗機夾具一組（其他夾具選購）。

★拉力試驗機專用測試軟件一份。

★品牌電腦一套、彩色打印機一臺(選配)。

6.1.1 觀測檢查和分辨力的判定

   通過實際試驗(或與其他檢測試驗結合進行)，在試驗過程中觀測檢查5.4.1.1、5.4.1.3和5.4.1.4。

   力指示裝置的分辨力r，應在試驗機的電動機和控制系統均啟動、在零試驗力的情況下按5.4.1.2的規定通過觀測和計算進行判定。

主要產品有：

拉力試驗機，                     塑料球壓痕硬度計

維卡熱變形試驗儀，               體積表面電阻率測試儀

海綿泡沫落球回彈試驗機，         海綿泡沫拉伸強度試驗機

耐壓試驗機，                 介電常數測試儀

海綿泡沫壓陷硬度測驗儀，         介質損耗測試儀

海綿泡沫疲勞壓陷試驗機，         薄膜沖擊試驗機

熔融指數儀，                     無轉子硫化儀

電壓擊穿試驗儀，                 摩擦系數儀

低溫脆性沖擊試驗儀               阿克隆磨耗試驗機等。

公司承諾：

1.購機前，我們專門派技術人員為您設計的流程和方案

2.購機后，將免費指派技術人員為您調試安裝

3.整機保修一年，產品終身維護

4.常年供應設備的易損件及耗品確保儀器能長期使用

5、售后管理：我公司實現計算機化管理，實行客戶定期電話回訪制度，定期復查設備的工作情況，定期電話指導用戶對設備進行保養和檢測，以便設備正常運轉，跟蹤客戶的設備使用情況，以便及時對設備進行維護

6、物流情況：及時提供貨源，確保全國范圍內2-10內到貨，持續穩定地為代理商做全面服務工作，提供合理的運作空間。公司有專業的技術人員為您安裝指導。

7、軟件升級：終生免費提供新版本控制軟件。

8、安裝培訓:儀器包裝內附有說明書，專業培訓人員為客戶指定操作者講解儀器正常操作流程、操作注意事項及儀器的日常維護要求；也可以根據客戶要求提供上門培訓服務。