老化、干燥、烘培試驗箱環境試驗箱  結構概述

   熱老化試驗箱是在原系列產品改型后的系列產品，此產品改型后，節能、美觀實用，容積100升、140升兩種規格。非規格可更根據用戶要求可特別加工，所有規格的老化試驗箱外殼體均采用優質鋼板焊接而成、表面烘漆，內室鋼板噴涂耐溫銀粉漆制成或不銹鋼制成，設有二至五成擱板。中間裝有支架轉盤，保溫層采用超細玻璃棉隔熱。箱門設有雙層玻璃觀察窗，工作室與箱門連接處裝有耐熱石棉繩，以保證工作室與箱門之間密封。老化試驗箱的電源開關、控溫儀等操作件均集中于箱體前面左側的控制處，按指示標操作。The thermal aging test chamber is a series of products that have been modified from the original series. After the modification, this product is energy-saving, aesthetically pleasing, and practical, with a capacity of 100 liters and 140 liters. Non standard aging test chambers can be specially processed according to user requirements. The outer shell of all specifications of aging test chambers is made of high-quality steel plates welded and baked on the surface. The inner chamber steel plates are coated with heat-resistant silver powder paint or made of stainless steel, and are equipped with 20% to 50% shelves. The middle is equipped with a support turntable, and the insulation layer is insulated with ultra-fine glass wool. The box door is equipped with a double-layer glass observation window, and the connection between the studio and the box door is equipped with heat-resistant asbestos rope to ensure sealing between the studio and the box door. The power switch, temperature controller and other operating components of the aging test box are concentrated at the control point on the left side of the front of the box, and operated according to the indicator.

   箱內加熱恒溫系統裝有風機、電加熱器、合適的風道結構和控溫儀組成，當接通電源時，風機同時運轉將直接置于箱內后側的電加熱產生的熱量通過風道形成循環風，經過工作室內干燥物品再吸入風機，如此不斷循環使溫度達到均勻。

   控溫儀為智能數顯顯示，具有控溫精度高，設定溫度帶有保護裝置和定時功能。

老化、干燥、烘培試驗箱環境試驗箱  注意事項

   1、箱外殼必須有效接地以保證使用安全。

   2、使用完畢后應將電源關閉。

   3、老化試驗箱無防爆裝置，不得放入易燃易爆的物品。

   4、老化試驗箱應放在具有良好通風條件的室內，在其周圍不可放置易燃易爆的物品。

   5、箱內物品放置切勿過擠，必須留出空間，以利熱空氣循環。

   6、箱內外應經常保持清潔。

   7、當使用溫度在150℃~300℃時，關機后應先將箱門打開降低箱內溫度。

主要數據

用途

       供工礦企業，化驗室科研單位作老化、干燥、烘培、熔蠟、滅菌之用。

使用方法

   1、將被干燥的物品放入老化試驗箱內，關好箱門后接通電源。

   2、把電源開關撥至‘開’處，此時電源指示亮燈，數顯控溫儀有數字顯示。

   3、控溫儀設定見附1。控溫儀顯示箱內有溫度，一般情況下，加熱90min后溫度控制進入恒溫狀態。（注意：智能型控溫儀參照下面‘操作方法’）

   4、當所需工作溫度比較低時，可采用二次設定方法，如需工作溫度80℃時，第一次可設定70℃，等溫度過沖回落時，再第二次設定80℃，這樣可降低甚至杜絕溫度過沖現象，使箱內溫度盡快進入恒溫狀態。

   5、根據不同的物品，不同的潮濕程度，選擇不同的干燥溫度和時間。

   6、干燥結束后，把電源開關撥至‘‘關’’處，但不能馬上打開箱門取出物品，小心燙傷，可先打開箱門降低箱內溫度再取出物品。

Usage

1. Put the dried items into the aging test box, close the box door, and then turn on the power.

2. Turn the power switch to the "on" position, and at this time, the power indicator light will be on, and the digital temperature controller will have a digital display.

3. The temperature controller setting is shown in Attachment 1. The temperature controller displays the temperature inside the box. Generally, after heating for 90 minutes, the temperature control enters a constant temperature state. (Note: For intelligent temperature controllers, refer to the 'Operation Method' below.)

4. When the required working temperature is relatively low, a secondary setting method can be used. If a working temperature of 80℃is required, the first setting can be 70℃. When the temperature overshoots and falls back, the second setting can be 80℃. This can reduce or even eliminate the phenomenon of temperature overshoot, allowing the temperature inside the box to enter a constant temperature state as soon as possible.

5. Choose different drying temperatures and times based on different items and varying degrees of humidity.

6. After drying, turn the power switch to the "off" position, but do not immediately open the box door to remove the item. Be careful of burns. You can first open the box door to reduce the temperature inside the box before removing the item.

產品保修承諾：

1、免費送貨到用戶指定的地點，免費指導安裝、培訓及調試。

2、保修期內人為損壞的零部件按采購（加工）價格收費更換。

3、保修期外繼續為用戶提供優質技術服務，在接到用戶維修邀請后3天內派工程師到達用戶現場進行維修。并享有優惠購買零配件的待遇。

4、傳感器過載及整機電路超壓損壞不在保修范圍內。

5、產品質保期：自安裝正常使用日起一年；

6、軟件升級：終生免費提供新版本控制軟件。

北廣產品銷往北京、上海、廣東、河南、浙江、河北、江蘇、湖南、內蒙、山東、四川、廣州、江西、西北、云南、深圳、吉林、南京、嘉興、佛山、蘇州、杭州、西安、潥陽、長春、江蘇、平頂山、安徽、金水、金華、海南、廊坊、天津、成都、揚州、東莞、濟南、南通、株洲、保定、貴州、宜興、嘉興、黑龍江、漳州、成都、重慶、咸陽、濟南、紹興、杭州、拉薩、山西、惠州、滄州、江西、沈陽、武漢、沈陽、昆明、鶴山、許昌、青海、寧波、醴陵、淄博、瑞安、阜新、合肥、長沙、常州、瑞安、青島、無錫、濟寧、醴陵、廈門、河源、樂清、煙臺、福州、龍口、徐州、唐山等地銷售。