熔體體積流動速率測試儀器  符合標準：

GB/T 3682《熱塑性塑料熔體質量流動速率和熔體體積流動速率的測定》

ISO 1133《塑料--熱塑性塑料熔體質量流動速率和熔體體積流動速率的測定》

JB/T 5456《熔體流動速率儀技術條件》

熔體體積流動速率測試儀器  熔體流動速率儀（液晶顯示、全自動）它采用微電腦（單片機）控制，中文操作界面，自動試驗結果；用于聚乙烯(PE)、聚丙烯(PP)、聚甲醛（POM）、聚苯乙烯（PS）、ABS塑料、聚碳酸酯(PC)等在高溫下熔體流動速率的測定 。

Complaint system and contact information

1. If you have any complaints about our service, please complain to the technical department dispatcher or maintenance department manager.

2. We are responsible for verifying the issues complained by users and will impose varying degrees of punishment on management and handling personnel. If it is not our responsibility, relevant personnel will also explain the situation to the user and help the customer solve the problem.

技術參數：

①　temperature range溫度范圍：室溫——400℃

②　Display resolution：?0.1℃

③　Display resolution顯示分辨率：0.1℃

④　Temperature recovery time溫度恢復時間：小于4分鐘

⑤　Cutting times切料次數：1—99次

⑥　Cutting time interval切料時間間隔：10—600秒

⑦　incubation time恒溫時間：可連續工作上萬小時

⑧　supply voltage電源電壓：AC220V?10%   50HZ

⑨　Outline size外形尺寸：寬?厚?高=250?350?510

Technical parameters:

①Temperature range: room temperature -400℃

②Display resolution:?0.1℃

③Display resolution: 0.1℃

④Temperature recovery time: less than 4 minutes

⑤Cutting times: 1-99 times

⑥Cutting time interval: 10-600 seconds

⑦Incubation time: can work continuously for tens of thousands of hours

⑧Supply voltage: AC220V?10% 50HZ

⑨Outline size: width?thick?Height=250?three hundred and fifty?five hundred and ten

可以測ＭFR值，配有打印機，手動自動兩種切料方式。具有操作簡便，控制精度高等優點。

擠壓出料部分

l 出料口直徑：Φ2.095?0.005毫米

l 出料口長度：8.000?0.025毫米

l 裝料筒直徑：Φ9.550?0.025毫米

l 裝料筒長度：152?0.1毫米

l 活塞桿頭直徑：9.475?0.015毫米

活塞桿頭長度：6.350?0.100毫米

投訴體系及聯系方式

1、 如果您對我們的服務有意見，請向技術部調度員或維修部經理投訴。

2、 對用戶所投訴的問題，核實是我們責任的，將對管理人員及經辦人員進行不同程度的懲處。如不是我司的責任，相關人員也將向用戶說明情況并幫助客戶解決問題。

Compliant with standards:

GB/T 3682 "Determination of Melt Mass Flow Rate and Melt Volume Flow Rate of Thermoplastics"

ISO 1133 "Plastics - Determination of mass flow rate and volume flow rate of thermoplastic melts"

JB/T 5456 Technical Conditions for Melt Flow Rate Meters

The melt flow rate meter (LCD display, fully automatic) is controlled by a microcomputer (microcontroller), with a Chinese operation interface and automatic test results; Used for measuring the melt flow rate of polyethylene (PE), polypropylene (PP), polyoxymethylene (POM), polystyrene (PS), ABS plastics, polycarbonate (PC), etc. at high temperatures.

It can measure the MFR value, equipped with a printer, and has two manual and automatic cutting methods. It has the advantages of simple operation and high control accuracy.

Extrusion discharge section

Discharge port diameter:Φ2.095?0.005 mm

Discharge port length: 8.000?0.025 mm

Loading cylinder diameter:Φ9.550?0.025 mm

Loading cylinder length: 152?0.1 mm

Piston rod head diameter: 9.475?0.015 mm

Length of piston rod head: 6.350?0.100 mm