離線在線一體總有機碳測試儀 超純水總有機碳分析儀  主要特征:

1、高精度、高靈敏度，操作簡單。

2、人性化操作界面，有一鍵運行功能，自動管路清洗功能。

3、高性能CPU，觸摸屏設計，超大640*480點陣真彩顯示器。

4、不用拆開機箱更換UV燈和泵管。

5、檢測上限可設定，自動上限報警功能。

6、具有RS232數據接口，歷史數據可存儲6個月。

7、離線檢測和在線檢測可選配。

8、具有打印功能

離線在線一體總有機碳測試儀 超純水總有機碳分析儀  差減法的表達式為TOC=TC－IC，即總有機碳是總碳（TC）與無機碳(IC)的差值。

TA-1.0分析儀采用的氧化方法是光氧化法：

H2O hn（185nm）‐> OH? H?OH? 有機物‐> CO2 H2O

二氧化碳的測量方式是差減法：TOC = TC－IC

TOC

為去除氧化生成的CO2，需將樣品的pH值再次降低。將CO2吹掃出來，并由特別開發的NDIR CO2檢測器進行測量。結果以總有機碳（TOC）方式予以顯示。

技術參數

1.電    源：AC220V?22V

2.電源頻率：50Hz?1hz

3.額定功率：100W

4.基本尺寸：44CM?18CM?26CM

5.檢測極限：0.001mg/L

6.檢測精度：?5%

7.檢測范圍：0.001mg/L～1.000mg/L

8.分析時間：4min

9.響應時間：15 min以內     within15min

10.樣品溫度：1-95℃

11.內部樣品流速：0.5ml/min

12.相對濕度：≤85%

13.重復性誤差：≤3%  

14.零點漂移：?5%

15.量程漂移：?5%

16.直 線 性：?5%

測試方法及其原理

國家藥典委員會發布的《中華人民共和國藥典2010版》二部中推薦采用在線和

離線兩種測試方法，還提供了系統適應性試驗的操作方法。同時對測試總有機碳的儀

器也提出了要求，即首先要能區分無機碳和有機碳；并能排除無機碳對總有機碳的影

響；其次應滿足系統適應性試驗的要求；最后儀器應具有足夠的檢測靈敏度。

要檢測樣品中的有機物濃度，必須將有機物分子分解并且轉化成能夠測量的單

分子形式，這樣就必須把有機物氧化成二氧化碳，并對生成的二氧化碳進行測量。目

前氧化的方法有四種：一、燃燒法；二、光氧化法；三、濕法氧化；四、光化學法。

氧化后有機碳測試的方法有差減法和直接法兩種。

工作原理

本儀器采用紫外氧化的原理，將樣品中的有機物氧化為二氧化碳，二氧化碳的測試采用的是直接電導率法，通過測試經過氧化反應的樣品的總碳含量和未經過氧化反應的樣品總無機碳的含量差值來測定總有機碳含量，即：總有機碳（TOC）=總碳（TC）-總無機碳（TIC）。

總有機碳分析儀可提供兩種更快更簡便的TOC檢測方法，即在線檢測和

離線檢測。

本測試系統提供了多種測試環境與測試方式，可以實現長期固定安裝的水系統

上的在線檢測，也可以使用自動連續和手動確認兩種方式實現TOC的離線檢測， 同

時系統具備歷史數據記錄和打印的功能。

工作原理

本儀器采用紫外氧化的原理，將樣品中的有機物氧化為二氧化碳，二氧化碳的測試采用的是直接電導率法，通過測試經過氧化反應的樣品的總碳含量和未經過氧化反應的樣品總無機碳的含量差值來測定總有機碳含量，即：總有機碳（TOC）=總碳（TC）-總無機碳（TIC）。

我廠主要產品有：維卡熱變形試驗儀，海綿泡沫落球回彈試驗機，海綿泡沫壓陷硬度測驗儀，海綿泡沫切割機，海綿泡沫疲勞壓陷試驗機，熔融指數儀，電壓擊穿試驗儀，塑料球壓痕硬度計，馬丁耐熱試驗儀，海綿泡沫拉伸強度試驗機，擺錘式?jīng)_擊試驗機，紙箱耐壓試驗機，門窗試驗機，防護材料沖擊試驗機，空氣彈簧力學試驗機，落鏢式?jīng)_擊試驗機，薄膜沖擊試驗機，電液伺服萬能試驗機，摩擦系數儀，電蒸汽鍋爐，大型電開水箱，地板耐摩擦試驗機，床墊耐沖擊試驗機，汽車座椅性能試驗機，安全帽沖擊/耐穿透性試驗機等。

Main features:

1. High precision, high sensitivity and simple operation.

2. Humanized operation interface, with one key operation function and automatic pipeline cleaning function.

3. High performance CPU, touch screen design, large 640 * 480 dot matrix true color display.

4. Do not disassemble the chassis to replace the UV lamp and pump pipe.

5. The detection upper limit can be set, and the automatic upper limit alarm function.

6. With RS232 data interface, historical data can be stored for 6 months.

7. Offline detection and online detection are optional.

8. With printing function

The expression of difference subtraction is TOC = tc-ic, that is, total organic carbon is the difference between total carbon (TC) and inorganic carbon (IC).

The oxidation method adopted by ta-1.0 analyzer is photooxidation method:

H2O HN (185nm) - > Oh? H?oh? organics) - > CO2 H2O

Carbon dioxide is measured by subtraction: TOC = TC－IC

TOC

In order to remove the CO2 generated by oxidation, the pH value of the sample needs to be lowered again. The CO2 was purged out and measured by a specially developed NDIR CO2 detector. The results are displayed as total organic carbon (TOC).

technical parameter

1. Power supply: AC220V?22V

2. Power frequency: 50Hz?1Hz

3. Rated power: 100W

4. Basic size: 44cm?18CM?26CM

5. Detection limit: 0.001mg/l

6. Detection accuracy:?5%

7. Detection range: 0.001mg/l～1.000mg/l

8. Analysis time: 4min

9. Response time: within 15min

10. Sample temperature: 1-95℃

11. Internal sample flow rate: 0.5ml/min

12. Relative humidity:≤85%

13. Repeatability error:≤3%

14. Zero drift:?5%

15. Range drift:?5%

16. Linearity:?5%

Test method and principle

Online and

The two offline test methods also provide the operation method of system adaptability test. At the same time, the instrument for measuring total organic carbon

The device also puts forward requirements, that is, first of all, it should be able to distinguish inorganic carbon from organic carbon; And the influence of inorganic carbon on total organic carbon can be eliminated

Ring; Secondly, it shall meet the requirements of system adaptability test; Finally, the instrument shall have sufficient detection sensitivity.

To detect the concentration of organics in a sample, the organic molecules must be decomposed and converted into measurable monomers

Molecular form, so that the organic matter must be oxidized to carbon dioxide, and the generated carbon dioxide must be measured. order

There are four methods of pre oxidation: first, combustion; 2、Photooxidation method; 3、Wet oxidation; 4、Photochemical method.

There are two methods for measuring the organic carbon after oxidation: subtraction method and direct method.

working principle

The instrument adopts the principle of ultraviolet oxidation to oxidize the organic matter in the sample into carbon dioxide. The direct conductivity method is adopted for the carbon dioxide test. The total organic carbon content is determined by testing the difference between the total carbon content of the sample after oxidation reaction and the total inorganic carbon content of the sample without oxidation reaction, that is, total organic carbon (TOC) = total carbon (TC) - Total inorganic carbon (TIC).

Total organic carbon analyzer can provide two faster and simpler TOC detection methods, namely online detection and

Offline detection.

This test system provides a variety of test environments and test methods, and can realize long-term fixed installation of water system

On-line detection of TOC can also be realized by automatic continuous and manual confirmation. The same as

The system has the function of historical data recording and printing.

working principle

The instrument adopts the principle of ultraviolet oxidation to oxidize the organic matter in the sample into carbon dioxide. The direct conductivity method is adopted for the carbon dioxide test. The total organic carbon content is determined by testing the difference between the total carbon content of the sample after oxidation reaction and the total inorganic carbon content of the sample without oxidation reaction, that is, total organic carbon (TOC) = total carbon (TC) - Total inorganic carbon (TIC).